il350, IL358 www.vishay.com vishay semiconductors rev. 1.5, 09-nov-12 1 document number: 83623 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 linear optocoupler for optical daa in telecommunications, high performance description the il350, IL358 family of linear optocoupler consist of an irled optically coupled to two photodiodes. the emitter mechanically faces both diodes enabling them to receive approximately an equal amount of infrared light. the diodes produce a proportional amount of photocurrents. the ratio of the photocurrents stays co nstant with high accuracy when either the led current changes or the ambient temperature changes. thus one can control the output diode current optically by controlling the input photodiode current. the il350, IL358 optocouplers can be used with the aid of operational amplifiers in closed loop conditions to achieve highly linear and electrically isolated ac and or dc signal amplifiers. features ? 2 mm high smd package ? high sensitivity (k1) at low operating led current ? couples ac and dc signals ? low input-output capacitance ? isolation voltage, 3000 v rms ? low distortion ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications ? optical daa for v.34 fax/modem pcmcia cards ? digital telephone line isolation agency approvals ? ul file no. e52744 system code s ? cul tested to csa 22.2 bulletin 5a note (1) also available in tubes, do not put t on the end. 1 2 3 4 5 6 7 8 k a nc nc k a k a k1 k2 i179028 ordering information i l35#t part number tape and reel agency certified/package k3 bin ul, cul, cqc 0.557 to 1.681 0.690 to 1.311 sop-8 il350t (1) IL358t (1) s op-# 8.4 mm
il350, IL358 www.vishay.com vishay semiconductors rev. 1.5, 09-nov-12 2 document number: 83623 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? stresses in excess of the abso lute maximum ratings can cause permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. note ? minimum and maximum values were tested requierements. typical va lues are characteristics of the device and are the result of e ngineering evaluations. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input reverse voltage v r 3v forward current i f 30 ma surge current pulse width < 10 ms i fsm 150 ma power dissipation t amb = 25 c p diss 150 mw derate linearly from 25 c 2mw/c output reverse voltage v r 15 v power dissipation p diss 50 mw derate linearly from 25 c 0.65 mw/c junction temperature t j 100 c coupler isolation test voltage t = 1 s v iso 3000 v rms total package power dissipation p tot 250 mw derate linearly from 25 c 2.8 mw/c storage temperature range t stg - 40 to + 150 c operating temperature t amb 75 c lead soldering time at 260 c 10 s isolation resistance v io = 500 v, t amb = 25 c r io v 10 12 v io = 500 v, t amb = 100 c r io 10 11 electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input forward voltage i f = 10 ma v f 1.8 2.1 v reverse current v r = 3 v i r 0.01 10 a v f temperature coefficient v f / c - 2.2 mw/c junction capacitance v f = 0 v, f = 1 mhz c j 15 pf dynamic resistance i f = 2.5 ma, i f = 1 ma v f / i f 6 switching time IL358/359 i f = 2.5 ma, i f = 1 ma t f 40 ns t f 40 ns output junction capacitance v f = 0 v, f = 1 mhz c j 12 pf nep v det = 0 v < 4 -14 w/ hz coupler capacitance (input to output) v f = 0 v, f = 1 mhz c io 1pf common mode capacitance v f = 0 v, f = 1 mhz c cm 0.5 pf
il350, IL358 www.vishay.com vishay semiconductors rev. 1.5, 09-nov-12 3 document number: 83623 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 switching characteristics - ac ch aracteristics photovoltaic mode parameter test condition part symbol min. typ. max. unit frequency response i p1 = 25 a, modulation current i p = 6 a IL358 bw (- 3 db) 1 mhz phase response i p1 = 25 a, modulation current i p = 6 a 45 rise time i p1 = 25 a, modulation current i p = 6 a 350 ns bin table bin min. max. a 0.557 0.626 b 0.620 0.696 c 0.690 0.773 d 0.765 0.859 e 0.851 0.955 f 0.945 1.061 g 1.051 1.181 h 1.169 1.311 i 1.297 1.456 j 1.442 1.618 coupled characteristics part number k1 at i f = 2 ma, v o = 0 v min. k3 bins il350 0.003 a to j IL358 0.008 c, d, e, f, g, h
il350, IL358 www.vishay.com vishay semiconductors rev. 1.5, 09-nov-12 4 document number: 83623 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example) note ? tape and reel suffix (t) is not part of the package marking i178013 40 3 to 7 10 typ. pin one id iso method a 5.7 5.5 8.4 0.25 5.8 5.6 2.3 2.1 1.09 0.83 1.25 typ. 0.41 typ. 0.38 0.05 1.05 ref. 0.15 typ. 1.27 r 0.25 6.76 9.04 7.28 0.250 1.19 0.05 1.14 0.36 0.91 IL358-e v yww s 68
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
